![]() To find the IP address of your host Linux PC you can issue the ip addr command from the shell or console. Tftpboot $ run importbootenv fi if test -n $uenvcmd then echo Running uenvcmd. U-Boot 2012.10-00077-g89d3a3e (13:11:33) DRAM: 1 GiB WARNING: Caches not enabled NAND: Micron MT29F2G08ABAEA, 128 KiB blocks, 2 KiB pages, 16B OOB, 8-bit NAND: chipsize 256 MiB In: serial. In the U-Boot console, set the IP address of the Host Linux PC that hosts the U-Boot loader file ( u-boot-sc584-ezkit.ldr) on TFTP. Run uenvboot run cp_kernel2ram & bootm 0x10000000 run netboot I suspect it is related to this error: Net: octeth0 Switch driver. Is there some option that will make a retry actually occur? Here is some environmental variables: > echo $default_bootcmd But it seems that I cant do any TFTP (tftpboot command). Note that I can use the serial port to manually restart the tftpboot, but I need it to retry automatically. I'm using a freshly compiled u-boot from u-boot-2016.09 source. ![]() I have an TFTP server set up as per INSTALLBANANAPI.TXT with a u-boot script, boot.scr, in /tftpboot. Once the server finally becomes ready, there is no communications to get the linux image. U-Boot tftpboot command requests a bootscript file, and needs the TFTP server IP address , and its own IP address . I've been playing around with this tonight. sudo screen /dev/ttyUSB0 115200) Interrupt U-boot process with , and boot OpenWrt initramfs by running: setenv bootcmd bootm 0xbf0a0000 saveenv tftpboot 2000000 .bin bootm 2000000 Copy (via scp).Easily upgrade IOS images, archive configuration files. Power on the router connect to U-boot over 115200-baud connection (usu. Once it times out, it will no longer attempt to connect to the server to get the file.: Filename 'image.ub'.Ä®ven though it says "starting again", nothing actually restarts. Use this free TFTP Server to move files to or from routers, switches, and other network devices. here XM is the size of initrd, if it is 8 MB give 8M. This can hardly be compared to NVRAM/TFFS-approach of other bootloaders. root/dev/ram0 rootfstypejffs2 rw initrd0x200000+offset,16M consolettyMCS mem64M0x0. Das U-Boot uses a small amount of space on the flash storage usually on the same partition it is stored on to store some important configuration parameters. However, if my device powers on before the server is ready, it will timeout. As per your bootargs provided in comment use. If the tftp server on an external device is already setup and running, everything works fine. cp 4.14 /tftpboot/ Kernel Boot Log: U-Boot SPL 2017. Since i have already setup the tftp server i just need to copy the kernel image into the tftpboot directory. +#ifdef CONFIG_CMD_TFTPSRV +static int do_tftpsrv(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv) + proto_t Ä®xtern charÄootFile /* Boot File name */Äiff -git a/net/net.c b/net/net.c index 2abf879.7a93542 100644 - a/net/net.c +++ b/net/net.I have u-boot configured to use tftpboot to grab the linux image over the ethernet network. This creates the linux kernel image which can be loaded into the pandaboard which is already running the locally compiled u-boot. + CONFIG_CMD_TFTPSRV * TFTP transfer in server modeĬONFIG_CMD_CDP * Cisco Discover Protocol supportÄiff -git a/common/cmd_net.c b/common/cmd_net.c index 8c6f5c8.b2c9355 100644 - a/common/cmd_net.c +++ b/common/cmd_net.c -52,6 +52,23 U_BOOT_CMD( Sender: -git a/README b/README index 6f3748d.ed73981 100644 - a/README +++ b/README -709,6 +709,7 The following options need to be configured:ĬONFIG_CMD_SOURCE "source" command Support Subject: TFTP: add tftpsrv commandĬontent-Type: text/plain charset="us-ascii" Wait a couple of minutes (first boot is always slightly slower) and enjoy your freshly reflashed Yún. OpenWrt-Yun will now start its boot process. U-Boot tftpboot command requests a bootscript file, and needs the TFTP server IP address , and its own IP address .X-OriginalArrivalTime: 10:04:21.0480 (UTC) After completing the above steps, if the U-Boot prompt appears, type the following command in the Serial monitor, followed by Enter : 1 bootm 0x9fea0000. Received: from ( )Ä«y (Postfix) with ESMTP id AC684280E4 NOT_IN_BL_NJABL=-1.5 (only DNSBL check requested) X-policyd-weight: NOT_IN_SBL_XBL_SPAMHAUS=-1.5 NOT_IN_SPAMCOP=-1.5 Received: from (localhost )Ä«y (Postfix) with ESMTP id 7F28D280FA Ä«y (Postfix) with ESMTP id 72BEF280C5 Received: from ()Ä«y localhost ( ) (amavisd-new, port 10024) Received: from localhost (localhost )Ä«y (Postfix) with ESMTP id B912D28114 X-Original-To: from ( )Ä«y (Postfix) with ESMTP id 304081007D1
0 Comments
Leave a Reply. |